When choosing a 4-port 10Gbps USB Hub, start with the peripherals that need to connect. If three devices with USB-A plugs must work at the same time, 3A+1C is the more practical fit. If two USB-C data devices need to stay connected to the hub at the same time, 2A+2C is the better fit. The same port count and rated speed can serve different combinations of devices.
For brands, distributors and procurement teams, the port mix is only the starting point. Upstream bandwidth, peripheral power requirements, port controls and sample validation also matter. Using PURPLELEC HB3025 (3A+1C) and HB3028 (2A+2C) as examples, this guide explains how to match the configuration to the intended setup.
Start with port counts and connection types
3A+1C means three USB-A downstream ports and one USB-C downstream port. 2A+2C means two of each. These are the ports for peripherals. The USB-C cable connecting the hub to the computer is the upstream connection and is counted separately. When planning the setup, count the plugs that will connect to the hub, rather than just the sockets on the devices themselves.

Port counts only; the diagram does not show the physical layout. The USB-C host connection is separate from the four peripheral ports. Both configurations specify an upstream link of up to 10Gbps, shared by high-speed devices.
USB-A and USB-C describe connector types; 10Gbps describes the data link rate. Check them separately. A USB-C connector alone does not establish support for 10Gbps data, USB Power Delivery (PD) charging or video output. USB-A can also carry a 10Gbps data connection. USB 3.2 Gen 2 is the 10Gbps data-rate category, while actual file transfer performance depends on the host, cables and peripherals. [1, 2]
HB3025 and HB3028: specification comparison
The comparison below reflects the two product specification sheets. Confirm the configuration you intend to order against the specification and sample agreed for your project.
| Specification | HB3025: 3A+1C | HB3028: 2A+2C |
|---|---|---|
| USB-A downstream ports | 3 ports, up to 10Gbps each | 2 ports, up to 10Gbps each |
| USB-C downstream ports | 1 port, up to 10Gbps | 2 ports, up to 10Gbps each |
| Host connection | USB-C, up to 10Gbps | USB-C, up to 10Gbps |
| Hub controller | GL3590 | GL3590 |
| Port controls and indicators | 4 individual port-control buttons with corresponding LEDs | 1 power LED; no individual port-control buttons listed |
| Specified upstream cable length | 15 cm | 15 cm |
Both specification sheets list GL3590. Genesys Logic describes it as a USB 3.2 Gen 2 hub controller with a 10Gbps upstream capability. The selection here therefore comes down to the USB-A/USB-C mix and the controls implemented in the finished product. An extra USB-C port, by itself, does not make a hub faster or establish that it is better built. [3]
HB3025's individual port controls are useful when peripherals need to be enabled or disabled separately. Its specification describes a short press to enable the corresponding port and a one-second hold to disable it, with an LED showing the port state. Safely eject a storage device through the operating system before disabling its port. For automation or power-control projects, confirm exactly how the buttons affect the data connection and power supply.
When 3A+1C is the better fit
Three USB-A peripherals that must work together are a straightforward reason to choose 3A+1C. For example, a USB-A keyboard-and-mouse receiver, a printer connected with a USB-A cable and a USB-A card reader use all three A ports. The C port is then available for a portable SSD connected with a USB-C cable. The count follows the cables used, not simply the type of peripheral.

HB3025 product image: 3A+1C downstream ports with individual port-control buttons.
For office accessory bundles or product ranges aimed at customers with existing USB-A peripherals, 3A+1C lets this mix connect directly and reduces the need for an adapter just to gain a third A port. Build the requirement around devices that must be connected at the same time. Spare devices used one at a time do not all need a permanent port.
Port type and bandwidth demand are separate questions. A keyboard, mouse or printer still operates at its own USB speed when connected to a 10Gbps port. A 10Gbps hub provides an appropriate data path for faster devices such as portable SSDs while also accommodating lower-speed peripherals.
When 2A+2C is the better fit
If two devices using USB-C data cables must work together, 2A+2C is the better match. For example, two USB-C portable SSDs, a USB-A keyboard-and-mouse receiver and a USB-A card reader need two C ports and two A ports. That combination maps directly to the 2A+2C layout.

HB3028 product image: 2A+2C downstream ports. The USB-C host cable is counted separately.
Some USB-C peripherals include a USB-C-to-USB-A data cable rated for the required speed. Take the supplied cables into account when selecting the hub. If customers should be able to use their existing USB-C-to-USB-C data cables, two C ports serve a specific need. If a third USB-A device must also stay connected, reconsider the port mix.
For distributor stocking decisions, use a list of the devices and cables your target customers need to connect. That gives you a practical basis for deciding which configuration to carry. The two layouts suit different peripheral combinations; the number of USB-C ports alone should not determine product positioning or price.
Why four 10Gbps ports do not add up to 40Gbps
HB3025 and HB3028 each specify one host connection rated at up to 10Gbps. USB 3.x traffic from high-speed peripherals shares that upstream link. Four downstream ports each rated for 10Gbps do not provide four independent 10Gbps paths to the computer when the devices transfer data together.

Generic shared-bandwidth illustration, not the port layout or measured performance of a specific model. The graphic shows 5Gbps and 10Gbps link rates; both configurations discussed here specify an upstream link of up to 10Gbps.
Copying files from one SSD while using a keyboard and mouse is a different workload from transferring large files on two SSDs at once. The latter calls for concurrent-transfer testing, but shared bandwidth is not fixed at 2.5Gbps per port: allocation changes as devices request and transfer data. Switching from 3A+1C to 2A+2C does not increase upstream capacity.
The host matters as well. If the computer's USB port supports only 5Gbps, a 10Gbps hub cannot upgrade that connection to 10Gbps. A slower peripheral also retains its own speed capability. For a project that needs two high-speed storage devices working together, record the host model, the specific USB port used, the cables and the SSD models. Then compare single-device and concurrent-transfer results. [1]
Check power, physical fit and sample performance
Two USB-C data ports should not be assumed to be two PD charging ports. Confirm any external power input, per-port output limits, the total power budget with all four ports in use, and whether the hub supports charging the computer. Only explicitly specified functions should appear on the packaging and sales page. Neither a 10Gbps data rating nor the GL3590 part number tells you the finished hub's power budget. [2]
Check physical fit on the actual sample. Wide USB flash drives, receivers and bulky cable plugs may block adjacent ports. Both specification sheets specify 15 cm for the upstream cable itself. Check how each hub will sit next to the target computer without pulling on its USB port. Once the port count fits the requirement, connect all intended peripherals to verify the arrangement.
| Sample check | What to test | What to record |
|---|---|---|
| Each data port | Connect a target high-speed device to each port; check the negotiated link rate and read/write performance | Host port, cable, device model and test conditions |
| Concurrent device use | Run transfers and other tasks with the intended peripheral combination | Aggregate throughput, individual device performance and any disconnections |
| Power and sustained load | Run the intended devices under the agreed power conditions for a sustained period | Power conditions, run time and any faults |
| Hot-plug and sleep/wake recovery | Check hot-plugging, reconnection and recovery after the host resumes from sleep | OS version, test steps and recovery results |
| Port controls and physical fit | Check button functions, LEDs and clearance between plugs | What each button controls, storage-eject steps and photos of the setup |
Agree acceptance criteria before testing. For a branded product, keep a record of the approved sample's specification revision, cable requirements and packaging claims. This helps keep purchasing, sales information and production deliveries consistent. Port counts and controller part numbers alone are not enough for product acceptance.
What to include in a procurement or OEM inquiry
For a useful quotation, turn a request for a four-port 10Gbps USB Hub into a specific connection requirement. Include the following:
- The target computer, OS version and rated speed of the host USB port.
- Peripheral models that must work together, and the number of USB-A and USB-C plugs that will connect to the hub.
- Whether two high-speed storage devices will transfer data at the same time, and the intended workflow.
- Separate requirements for individual port control, external power, peripheral charging and host charging.
- Expected order quantity, target market, branding and packaging requirements, and any requested hardware or feature changes.
Start with 3A+1C if three USB-A ports are essential, or 2A+2C if two USB-C ports are essential. Then validate bandwidth, power and control behavior using the same host and your intended peripherals. PURPLELEC HB3025 and HB3028 provide two configurations to compare; the specification revision and sample agreed for the project should remain the reference for the order.
Frequently asked questions
Is 2A+2C faster than 3A+1C?
Not by itself. Both configurations discussed here specify upstream and downstream data links of up to 10Gbps. The A/C split changes the connection mix. Actual performance still needs to be checked with the intended host, cables and peripherals.
Can two USB-C ports support two portable SSDs at the same time?
Two USB-C data ports are an option for this setup, but verify the target devices, cables and power conditions on the sample. When the SSDs transfer data to the host together, they share upstream bandwidth. Do not budget for an independent 10Gbps upstream path for each SSD.
Can a USB-C downstream port drive a monitor?
Video output must be explicitly supported. A USB-C data connector alone is not evidence of DisplayPort Alt Mode output. If the project needs a display connection, list and verify that capability separately.
Should I choose by the controller or the port mix?
Check both. The controller determines which data architectures are possible, while the port mix determines how peripherals connect. For products listing the same controller, also compare the power design, port controls, cables and sample performance.










